Skip to content

Diesel at a crusher plant: issue registers, hour meters and litres per tonne

Yellow wheel loader working at a stone quarry

Ask a crusher owner what the plant spent on diesel last month and you will get a figure from the fuel bills. Ask how many litres went into the loader against how many hours it worked, and the answer is usually a guess. Diesel is one of the largest running costs at a crusher and one of the easiest to lose, because it is liquid, it is valuable and it is handled by many people every day.

This post sets out a simple diesel control routine for a crusher plant: one issue register, hour meter readings, two ratios worth watching and the monthly checks that show where fuel goes.

Where diesel goes at a crusher

Most plants burn diesel in four places, and each one needs its own line in the register:

  • Generator sets, where the plant is not on grid power or runs a backup during cuts.
  • Loaders and excavators feeding the primary hopper and loading trucks.
  • Own tippers and trucks carrying raw stone from the face or delivering to customers.
  • Small users such as compressors, water tankers and the rock breaker.

If all of this is recorded as one monthly total, you cannot tell a hungry machine from a leaking one or a dishonest one.

One issue register, filled at the pump

Every litre that leaves the storage tank or the bowser should be written down at the moment it is issued, not at the end of the shift. Each entry needs:

  1. Date and time of issue.
  2. Machine or vehicle number.
  3. Hour meter or odometer reading at the time of filling.
  4. Litres issued.
  5. Name of the operator or driver who received it.
  6. Name of the person who issued it.

The hour meter reading is the column that makes the register useful. Without it, you only know how much fuel went out. With it, you know how much work the fuel bought.

Purchases go into the same register: tanker or pump receipts with the invoice number, litres received and dip readings before and after unloading. Book stock is then opening stock plus receipts less issues, and it can be checked against a dip every morning.

Two ratios worth watching

Litres per hour for each machine

For loaders, excavators and generator sets, divide litres issued by hours run between two fillings. Each machine settles into its own normal range depending on its age, its load and the operator. Do not compare against a brochure figure; build a baseline from your own three good months.

Once you have the baseline, the useful signal is a change. A loader that moves from its usual range to noticeably more litres per hour with no change in work is either due for service or losing fuel.

Litres per tonne for the plant

Divide all diesel used at the plant in a month by tonnes produced. This is the number that goes into your cost per tonne, and it moves with power cuts, feed quality and breakdowns. Look at it next to your production figures from the stock and production report, not on its own.

Common leakage points

What happens How it shows up What catches it
Fuel issued but not put into the machine Litres per hour rises with no extra work Hour meter reading at every filling, operator signature
Short receipt from the supplier Dip after unloading is less than the invoice Dip before and after every delivery
Hour meter not working or disconnected Same reading on two fillings Register refuses an entry with an unchanged reading
Fuel drained from parked vehicles Truck needs more fuel for the same trip Litres per trip compared with past trips on the same route
Issues written up later from memory Round numbers, entries in one handwriting Entry at the pump, time-stamped by the software

Diesel and GST

High speed diesel is currently outside GST, so the bill carries state VAT and central excise rather than GST, and there is no input tax credit on it. That makes every litre a straight cost to the plant, which is one more reason to track it closely. Confirm the treatment of your fuel and lubricant bills with your CA, because lubricants and other petroleum products are taxed differently.

A monthly diesel review

  1. Reconcile book stock with the dip on the last day of the month.
  2. List litres per hour for every machine against its own baseline.
  3. Flag any machine that moved outside its normal range and ask why.
  4. Check litres per tonne against production and power-cut hours.
  5. Match supplier invoices with receipts in the register before paying.

Frequently asked questions

Our machines do not have working hour meters. What can we do?

Fix them first, because the meter costs far less than the fuel it protects. Until then, have the supervisor record start and stop times for each machine on the shift sheet and use those hours.

Should own trucks be tracked by trip or by kilometre?

Both, if you can. Kilometres from the odometer or GPS are the base, and litres per trip on regular routes is the quick check. Our note on vehicle and trip records covers trip logging.

Is a paper register enough?

It works if it is filled at the pump and checked daily. The weakness is that nobody adds up litres per hour until month end, by which time the fuel is gone.

Where this fits

Diesel control works best when issues, machine hours and production sit in one system. Quipu’s Stone Crusher and Quarry ERP keeps the vehicle and dispatch log, GPS tracking for trucks and the plant dashboard together, so fuel can be seen against the work it paid for. Book a demo to see it with your own figures.

Keep reading

WhatsApp